Wyniki 1-5 spośród 5 dla zapytania: authorDesc:"Paulina Indyka"

Mechanical and tribological properties of electrodeposited Ni-Mo coatings

Czytaj za darmo! »

Hard chromium coatings are widely used in aerospace, automotive, hydraulic and machinery industry to reduce friction, wear and corrosion. Electrodeposition is a frequently used technique to deposit such a coatings because is simple, low cost and low temperature. Main advantage is to possibility of relatively uniform deposition on large, complex shape elements. Nowadays hard chromium that dominates within this group coatings were characterize by good mechanical and corrosion resistance but the deposition process is toxic and carcinogenic. Many environmental friendly materials are proposed to replace electroplated chromium coatings, and one of them are nickel based alloys coatings - Ni-P [1], Ni-Mo [2], Ni-W [3] and nanocomposite coatings like Ni-P-Al2O3 [4], Ni-W-SiC [5]. Pure Ni coatings are not hard and wear resistant, but their properties could be significantly improved by alloying and reducing the grain size to nanocrystalline structure. It is reported that Ni-Mo deposits have a good corrosion resistance but there is a lack of tribological studies. For coating-substrate systems wear is not only determined by hardness as showed classical theories of friction [6]. Increase of hardness is usually associated with rise of stiffness and frequently cause change of deformation mechanisms from plastic to brittle fracture. Many studies indicate than wear depends on quotient of hardness H and modulus of elasticity E [7] which is called plasticity index. This value can be used to quantitatively assess the load that may be carried on by the coating in the elastic stress regime. Wear at the elastic state, when abrasive wear dominates is significantly lower than under plastic deformation. The value of the contact force that caused plastic deformation of the coating can be calculated from Hertz theory [8]: P R R pl E l ind = 0 68 3 ⋅ ⋅ 3 2 2 . π (1) where Eind is the reduced modulus of elasticity of coating and the [...]

Optimization of galvanic bath and operating parameters for amorphous Ni-W electrodeposition

Czytaj za darmo! »

Functional coatings obtained by electrodeposition are widely applied commercially to provide enhanced surface performance for engineering applications [1]. In recent years much effort has been put into searching for alternatives to electroplated hard chromium, the properties of which are often used as a standard for other functional coatings [2]. Usually, high hardness, wear and corrosion resistance are the critical properties. Despite the excellent properties of the hard chromium coatings, used in automotive and aviation industries, they should be eliminated from the manufacturing process (according to the EU directives), due to high toxicity and carcinogenity of hexavalent chromium. Up to now, only electroless hard Ni and Ni-P coatings have found use in selected applications [3]. Electrodeposited Ni-based alloys containing refractory metal (molybdenum or tungsten) could be an important alternative to hard chromium. Ni-W alloys are known for their excellent mechanical and tribological characteristics, but they are very difficult to obtain by conventional metallothermic methods, due to the large differences in melting points (Ni - 1455°C, W - 3410°C) as well as limited mutual solubility of both metals [4]. Hence, electrochemical deposition can be proposed as an alternative technique. Electrodeposition, as a cheap, low temperature and simple method, is a superior technique for manufacture of Ni-W coatings. However, compact and well adherent to the substrate Ni-W coatings are still electrodeposited with technical difficulties. Although tungsten cannot be separately electrodeposited from aqueous electrolytes, it can be easy co-deposited with iron-group metals such as nickel to form an alloy [5]. However, the presence of appropriate complexing agents is necessary. This phenomena is classified by Brenner as induced co-deposition [6]. Among many galvanic baths proposed for the Ni-W alloys electroplating (such as sulfamate, pyrophos[...]

Electrodeposition of nanocrystalline Ni-Mo coatings from citrate electrolyte solution

Czytaj za darmo! »

Alloys containing molybdenum, e.g. Ni-Mo, are characterized by high hardness, high wear, thermal and corrosion resistance as well as good catalytic properties for hydrogen evolution in alkaline solutions. They also offer an important alternative to hard chromium coatings as chromates are known to be highly toxic and according to EU directive they should be eliminated from manufacturing process, e.g. in automotive and aviation industries [1]. However, these alloys are difficult to prepare by conventional thermal methods due to the large differences in their melting points (Ni - 1455°C, Mo - 2620°C) and their limited mutual solubility [2]. Several techniques have been proposed for the Ni-Mo alloy preparation: mechanical alloying, plasma sputtering, gas condensation and electrocrystallization. Electroplating is a relatively simple, low cost and low temperature method suitable for mass production, where the substrates of complex shape can be uniformly plated by coatings with high rate. However, it is known that molybdenum in a metallic state cannot be separately electrodeposited from an aqueous solution of its salts, but it can readily be co-deposited with iron-group metals such as nickel, forming an alloy. The phenomenon is called induced co-deposition [3]. The mechanism is still not clearly understood, although a few hypotheses are presented in literature [3÷6]. The electrodeposition of Ni-Mo alloys have been extensively investigated [7÷11]. A great number of galvanic baths were studied, e.g.: sulphate, sulpho- salicylate, acetate, tartrate, pyrophosphate, amonia and citrate. Most deposits obtained from these baths were poor quality, porous or cracked and electrodeposition process was not efficient, however pyrophosphate and citrate electrolytes are the most promising. In the present work the correlation of electrodeposition conditions from citrate solution with the coating properties was determined. The surface morphology as a f[...]

Alkaline leaching of amphoteric elements from powdered, overstoichiometric hydride material DOI:10.15199/40.2015.11.2

Czytaj za darmo! »

The alkaline preferential dissolution of amphoteric elements from overstoichiometric, powdered hydrogen absorbing material of LaNi4.5Co0.5(AlZnSn)0.35 composition has been studied using ICP AES method. The observations of structure changes of the as received and leached material particles have been studied by XRD and TEM techniques. It has been shown that during 50 h exposure of the powder in 6 M KOH (38oC) over 50% of amphoteric elements are selectively etched from the tested material. At the same time, as a result of etching, the surface layers of powder particles undergo strong development. Keywords: hydride alloy, amphoteric additions, selective leaching, alkaline solution Ługowanie pierwiastków amfoterycznych z nadstechiometrycznego wodorkowego materiału proszkowego w roztworze alkalicznym Metodą ICP AES analizowano preferencyjne wytrawianie pierwiastków amfoterycznych z nadstechiometrycznego materiału wodorochłonnego o składzie LaNi4.5Co0.5(AlZnSn)0.35. Zmiany strukturalne wyjściowych i trawionych cząstek materiału obserwowano za pomocą technik XRD i TEM. Pokazano, że 50-godzinna ekspozycja badanego proszku w 6 M KOH (38oC) prowadzi do selektywnego roztworzenia ponad 50% pierwiastków amfoterycznych obecnych w wyjściowym materiale. Jednocześnie, w wyniku wytrawiania proszku, powierzchnia zewnętrznych warstw cząstek ulega silnemu rozwinięciu. Słowa kluczowe: stop wodorochłonny, dodatki amfoteryczne, selektywne wytrawianie, roztwór alkaliczny 1. Introduction Among requirements most commonly appointed for alloys absorbing atomic hydrogen (in short: hydride alloys) suitable for application in NiMH-type batteries, the most commonly are mentioned: high capacity, good electrochemical catalysis, easy formation, acceptable corrosion resistance, suitable hydrogen equilibrium, long cycle life, small pressure-concentration-temperature hysteresis, and low cost [1, 2]. To ensure desirable properties to hydride materials the alloying of parent [...]

Characterisation of TCP phases in CMSX-4 single crystal superalloy subjected to high temperature annealing and creep deformation DOI:10.15199/28.2016.4.1


  A high temperature exposure of nickel-base single crystal superalloys leads to a formation of topologically close packed (TCP) phases, what can deteriorate their creep strength. Therefore, the aim of the present work was to investigate TCP phases precipitated in CMSX-4 superalloy after a two-step treatment consisting of annealing at temperature of 1100°C followed by a creep deformation at temperature of 900°C. The microstructure of CMSX-4 superalloy exposed to a high temperature was investigated by means of scanning and transmission electron microscopy as well as scanning-transmission electron microscopy in high angle annular dark field mode. The chemical composition in nanoareas was determined using the high spatial resolution and high count rate energy dispersive X-ray spectroscopy. A three-dimensional characterization of the microstructure of annealed and creep tested single crystal superalloy was carried out by means of electron tomography. Results of microstructural investigation have shown that after the application of two-step high temperature exposure the TCP precipitates present in CMSX-4 superalloy are P and μ phases. The most pronounced differences in the chemical composition of the investigated P and μ phase particles are concerned with W and Re content. It was determined that the P phase contains a higher amount of W, while the μ phase is mostly rich in Re. Key words: single crystal nickel-base superalloys, annealing, creep, TCP phases.1. INTRODUCTION Single crystal nickel-base superalloys are especially designed for gas turbine blade and vane applications. The microstructure of single crystal superalloys consists of two phases, namely the γ phase matrix and cuboidal γʹ phase precipitates. To increase the high temperature creep resistance of single crystal superalloys, high amounts of refractory elements such as Mo, W and Re are added. These elements provide a solid solution strengthening, but unfo[...]

 Strona 1